During the construction of an industrial facility, much attention is paid to the strength of the service pipelines fasteners. It is also necessary to provide reliable connection of all units of industrial equipment with the pipelines. In this case, it is not always possible The use of a permanent welded joint is not always possible, therefore, there are various types of weld-free tight joints.
FLANGE JOINT COMPONENTS
At present, one of the most effective connections used in industrial facilities is a flange joint. This is an airtight connection that provides high structural integrity, consists of two flanges, fasteners (studs or bolts, washers, nuts) and gaskets.
An important matter in choosing a set of flanges is tightness. The gasket material must have good elasticity, strength, resistance to the operating temperature conditions and to the media with which direct contact is expected.
For flange joints, Villina company uses the following types
Les capsules de boissons fonctionnelles pour la beauté et la santé Sentastiq sont compatibles avec les machines à café Nespresso. Ils présentent un grand choix de saveurs que chacun trouvera le goût d'aimer. La composition fonctionnelle de chaque boisson est développée par des médecins et des scientifiques. Les boissons fonctionnelles Sentastiq vous aideront à rester en bonne santé pendant des années.
THOR represents one or two superpowerful loudspeakers housed in spheroidal structures made of titanium-steel alloy. The system is suitable for absolutely any modern car. You will only need CAN-bus of your car`s engine to install THOR system. It is CAN-bus via which a complete synchronization of electronic exhaust system and your engine operation is performed. Installation warranty is two years. Service life of the device is unlimited.
The device is designed and manufactured in Russia.
ADVANTAGES
- Maximum volume and similarity of sound
- Does not void car warranty
- Over 20 legendary sport car sounds
- Service life over 10 years
- Custom settings: volume, pops, dynamic start etc.
Suitable for any car from model year 2005.
System installation
- Install speaker acoustic system at the car bottom
- Connect THOR electronic control unit to CAN and ACC circuits
- Connect system components
- Install THOR app. The system is ready for operation.
We supply thrust bearings (bearing plates, end thrust bearing), rolling bearing (combined type) and support bearings (plain journal bearings) made of the following material: tungsten carbide (WC); silicon carbide (SiC), VK8 alloy, etc.
IEEE 802.3/802.3u/802.3ab/802.3x/802.3at/802.3af, 4 ports PoE 30W
8K MAC, 1Mbit buffer, Switch fabric 12 Gbps
PoE Pin Assignment: 1/2(+), 3/6(-). Mode A EndSpan PoE
Housing:IP30 Protection, DIN Rail or Wall mounting (included)
Operating Temperature:- 40 to 75 °C (-40 to 167 °F)
Operating Humidity:Max. 95 % non-condensing
Dimensions:142 x 105 x 43 mm
Weight:720 g (1 lb)
EMI:FCC Part 15 Subpart B Class A/ CE EN 55022 Class A
EMS:IEC61000-4-2 (ESD) /IEC61000-4-3 (RS) /IEC61000-4-4 (EFT) /IEC61000-4-5 (Surge) /IEC61000-4-6 (CS)
Certifications:CE, FCC
Free fall / Shock / Vibration:IEC60068-2-32 / IEC60068-2-27 / IEC60068-2-6
Warranty:3 years (up to 5 years)
MTBF:510,400 hours
The magnetic coupling drives for stirring devices are designed to be installed immediately into the tank and provide the necessary stirring of the product. The drive is electrically driven and consists of two half-couplings (driven and driven magnetic half-couplings), bearing assembly and the stirring device itself. Stirring devices (mixers) are of several types: paddle, anchor, propeller, U-type, etc.
We develop and supply turn-key solutions for our customers. Magnetic coupling drives for stirring devices are custom-tailored for each specific customer's application in accordance with the sketches provided or according to the parameters specified in the questionnaire form.
We supply rubber sealing O-ring comforming with GOST 9833-73 “Rubber sealing O-rings”.
We produce:
flat paronite and fluoroplastic gaskets in accordance with GOST 481-80
high-temperature TEG (thermally expanded graphite) gaskets according to STO 00220575.001-2007
heat-resistant spiral-wound gaskets according to GOST R 52376-2015
We produce shafts for pumping units made of the following materials: steel 20H13, 30H13, 40H13 as per GOST 5632-2014; GOST 5949-2018; 14H17N2 as per GOST 5949-2018. Shafts made of other materials are also available subject to prior agreement.
Subject to preliminary agreement, we are able to supply larger diameter shafts. All parts are manufactured according to drawings.
Maximum length:up to 2 meters
Maximum diameter:100 mm